How To Test Car Battery Amps With Multimeter

Car battery is the main component of a vehicle, anything negative that happens to a battery will have a direct effect on an entire car, you may not be able to turn on the engine, lights stop working and etc. therefore a period checkup must be needed to ensure the battery is working at full capacity.

There Are Certain Steps Which Guides Of How To Test Car Batter Amps With Multimeter

Step – 1

Test Your Meter

The first thing you need to do is check your meter; this can be achieved by setting the functions to ohms. The readings should be about zero when you connect the test leads, and the readings should be 1 when the relation is split. If your battery does not follow this pattern then something is wrong with the pattern.

  • Types of Meter

There are commonly two types of multimeter available for purchase in the market—analog multimeters and digital multimeters. While digital multimeters showcase a numeric display, analog multimeters provide readings through the use of a microammeter with a moving pointer.

Step – 2

Set Multimeter at 20v Volt

Set Multimeter at 20v Volt

If you have a dedicated car battery test range, select the DC volts location on your multimeter (or the 12V setting). Typically the DC voltage is marked as a V followed by a short line with a dotted line under it. The wavy line after a V is voltage AC (alternating current), and is used to test the voltage of your house’s mains.

Most of the manual ranging meters have a 20V range, which is what you would need to test a car battery. The 20V range means it will measure between 0V and 20V. See below.

Find More: IS A BRAKE FLUID FLUSH NECESSARY?

Step – 3

Turn the off ignition and radio

Turn the off ignition and radio

You need to have the engine turned off and radio to test the car battery using a multimeter.

Step – 3

Find a car battery location

Find a car battery location

The battery for the car is mainly in the engine room. Open and search for the battery close to engine.

Step – 4

Connect the Multimeter to your Batteries

Connect the Multimeter to your Batteries

A proper multimeter like Fluke 87V will come with two cords on one end with a probe and a lead on the other. So make sure you insert the cords into correct ends.

Connect it positive to positive and negative to negative.

  • Connect Positive Probe

Connect Positive Probe

The red cable or lead of your multimeter should be plugged into the + port and connected to the positive terminal on your car battery.

Find MoreWhy Is My Car Air Conditioner Not Blowing Cold Air?

Find More: How To Test Cold Cranking Amps With A Multimeter?

  • Connect Negative

Connect Positive Probe

The black cable should connect to the – port ( Neg, Ground) on your digital multimeter and also the negative terminal on your car battery.

Step – 5

Measure Voltage

Once you turn the multimeter on and set the voltage range properly, the multimeter will show the voltage of the battery.

  • How to read Meter Reading

Car batteries provide 12.6V DC (direct current) through six cells, producing 2.1V each.

Voltage

Charge Status

Engine Running: 13.7 to 14.7 volt

GOOD

Engine Off

Charge Status

12.6V: fully charged 100% Charged – GOOD
12.4V: 75% charge 75% Charged – GOOD
12.2V: 50% 50% Charged – Needs Charge
12V: 25% 25% Charged – Needs Charge
11.9V and below: effectively zero charge Battery Discharged

Just because the battery reads more than 12.6 volts does not always mean that the battery is fine. The battery can read more than 12.4 volts, but not enough Cold Cranking Amps (CCA) output to start the engine. You’ll learn how to conduct a battery charging test in the next part.

Test a car battery using a multimeter by putting Load

Load is applied to the battery while its voltage is monitored. You can do this by starting the engine, turning lights on and monitor the voltage with a multimeter that has a min/max mode. This will automatically store the high and low voltages it picks up. The high voltage will likely be in the 14v area and is perfectly normal, while a drop under 9.6v during the process would indicate it can no longer effectively hold charge and needs changing.

Find More: How to Clean a Radiator with Baking Soda

Check Battery status

Anything under the 75% charge rate, or about 12.45V, generally indicates the battery is undercharged and will need recharging. It does not, however, indicate that it is bad. If after recharging it doesn’t hold the charge, then there are other problems that needs to find it out.

Before finding other problems you need to first charger the battery

1st Method

  • Many car owners simply jump-start the car and let the alternator charge the battery.
  • While letting the alternator charge the battery works in most cases it is not the best method to charge a car battery.

2nd Method (Recommended method)

  • Get any 12-volt Trickle Charger.
  • Connect the red positive clamp to the battery positive terminal.
  • Connect the negative clamp to the negative battery terminal.
  • Note: Many vehicles have battery jump-starting terminals under the hood. In most cases, car manufacturers recommend that you use the jump terminals to charge the battery

If The Car Battery Still Dying Out Quickly Then?

Other problems

Bad Connections

Bad Connections

When some corrosion occurs around the battery terminals, the connection may be interfered with, and the vehicle may have trouble starting. It may be attributed to corroded or even loose terminals of the batteries. When the key is turned, the vehicle can experience difficulty starting, slow cranking, or fast clicking.

Short Circuit

A common type of short circuit occurs when the positive and negative terminals of a battery are connected with a low-resistance conductor, like a wire. With a low resistance in the connection, a high current will flow, causing the delivery of a large amount of energy in a short period of time.

Alternator at fault

Alternator at fault

A very simple way to check if the alternator is working is to run the car and disconnect the positive terminal of the battery. If the vehicle stops running, then you probably have a bad alternator.

You can also inspect your interior and dashboard lights. If you note that the lights shine brightly but gradually fade over time, then you’ve got a poor alternator on your hands. It is because while the battery starts the ignition and the lights, it still depends on the alternator to continue to operate while the car is running. So if the lights come on but don’t have the same brightness then the battery isn’t charged properly.

Find More: What To Do When Car Is Overheating 6 Step To Follow

Battery need replacement

These are only a couple of the key explanations for the need to replace a car battery.

  • Old battery
  • Slow to start
  • Cranks or clicks but won’t start
  • Dash lights work, car won’t start
  • More frequent jump starts

About The Author

Avatar for Ibrar Ayyub

Ibrar Ayyub

I am an experienced technical writer holding a Master's degree in computer science from BZU Multan, Pakistan University. With a background spanning various industries, particularly in home automation and engineering, I have honed my skills in crafting clear and concise content. Proficient in leveraging infographics and diagrams, I strive to simplify complex concepts for readers. My strength lies in thorough research and presenting information in a structured and logical format.

Follow Us:
LinkedinTwitter
All About Cars News Gadgets >> Auto Repair >> Common Issues >> How To Test Car Battery Amps With Multimeter

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top